1. Welcome to brand new satellite community! Join now if you want to enjoy in discussions and participate in contests where you can earn awards.
    Dismiss Notice

Install oscam on vps

Discussion in 'VPS Support' started by OldSkul, Oct 4, 2013.

  1. wuming4

    wuming4 New Member

    Hi m8,

    Thanks for all the help, i managed to get the VPS connected to my local server.
    If i wanna connect extra cards (same CAID) to local server, do you guys recommend different grp + different users or different grp + 1user for VPS?
    Tiers are different between the cards.

    Local Server: 3 cards (Grp 1) ---> 1 user (Grp 1) ----> VPS : 1 remote reader (newcamd)


    Local Server: 3 cards (Grp 1,2,3) ---> 1 user (Grp 1, 2,3) ----> VPS : 1 remote reader (newcamd, grp)


    Local Server: 3 cards (Grp 1, 2, 3) ---> User A (Grp 1) + User B (Grp 2 ) + User C (Grp 3) ----> VPS: 3 remote readers (newcamd)

    I believe all the 3 above setup should work but which is the best practice i should adapt?
    Million thanks in advance as i am still learning. :)

  2. OldSkul

    OldSkul Administrator Staff Member

    I personally use third option as you have better overview of your readers/cards.
  3. LupoSol

    LupoSol New Member

    Hello again friends at satnigmo!

    I would like to add to the VPS a second card of mine I have in a separate location (a 09CD Italian card), on a different decoder with (of course) a different IP address.

    Can the same instructions that you gave me above (and which work perfectly!) also be extended to this second card?

    If so, can I use the same port 12012 for newcamd I am using for CAID 183D?

    If it is possible, what changes/additions do I have to add on each side?

    Thanks a lot, once again!
  4. xyrius

    xyrius New Member

    in oscam.conf
    port = 5500@0500:032830;5501@0100:003311 # one port for eacxh caid card
    key = 0102030405060708091011121314
    LupoSol likes this.
  5. OldSkul

    OldSkul Administrator Staff Member

    Add new newcamd port for your 09CD card on second decoder and then just follow instructions you already know.
  6. LupoSol

    LupoSol New Member

    Hi to you too! :)

    I take it this must be on the VPS osam.conf, correct?

    Then, as OldSkul suggested, I follow the same instructions I know on the second decoder, correct? :)

    Thank you so much!
  7. wuming4

    wuming4 New Member

    HI m8,

    With the help from here, i managed to setup the VPS.
    But from ecm from cache, why do i still have lag like

    cache2 (627 ms) by Reader-1 (P/1/2/3)

    At times, i will get below results which i hope to get everytime
    cache1 (0 ms) by Reader-1 - (cw count 3)

    Is it sometime wrong with my config or is it normal?
    I can post my config if someone is willingly to help to check. Thanks. :)

  8. OldSkul

    OldSkul Administrator Staff Member

    If you have normal picture then dont worry ...
  9. kuki01

    kuki01 New Member

    panowie może ktoś ma instrukcje Pl jak sie takiego vpsa konfiguruje
  10. OldSkul

    OldSkul Administrator Staff Member

    English pleaes
  11. nightmares

    nightmares New Member

    i think to use camd35 instead of newcamd as i have noticed that necamd has o lot of disconnection between 2 oscam , but its just my opinion
  12. OldSkul

    OldSkul Administrator Staff Member

    I cannot confirm this, newcamd connection works fine ...
  13. mrpotato

    mrpotato New Member

    I need connect my local card to vps via cccam because I don't have public IP.
    Can I do like that?
  14. carticiano

    carticiano New Member

    hello to all friends of the forum, I have a problem I bought a vps is I can not install the oscam it to put the dyndns, is there anyone who can give me a hand?
  15. OldSkul

    OldSkul Administrator Staff Member

    Please explain more.
  16. asddds

    asddds New Member

    I followed the guide to install oscam on vps server.
    I'm using as a server vps misterhost.de.
    I came to ./simplebuild menu
    Now I do not know how to upload the configuration file.
    What should I do?
  17. OldSkul

    OldSkul Administrator Staff Member

    What do you mean? Simplebuild works without adding any config files.
  18. asddds

    asddds New Member

    sorry, but I'm going mad, I need you to help me step by step.
    I bought vServers OpenVZ vServers-S Webhosting,Rootserver,Business Server,Housing,DomainsMisterhost.de I paid 1.99 Euros.

    I follow your guide on how to compile the oscam and get to the point where I do ./simplebuild menu.

    I can not figure out what to do here.

    After compiling oscam for you VPS, you need to put oscam executable file to / usr / local / bin folder on your VPS server. Use 0755 permissions for this file. Then you need to put oscam configuration files to / usr / local / etc folder. You need oscam.user, oscam.conf and oscam.server. Just create empty files With These names and upload them to / usr / local / etc folder. One setting is very important in oscam.user and That Is httpallowed! You Should this September to: httpallowed = IPOFYOURCOMPUTER (NOT LOCAL NETWORK IP !!)
    Now you need to run oscam with this command: -b ./oscam
  19. asddds

    asddds New Member

    after that I fill out the oscam how do I set up files and oscam.server oscam.user?
  20. asddds

    asddds New Member

    I managed to compile oscam and oscam server and enter oscam client.
    but if I do ./oscam -b does not work

Share This Page